Veigel BHA23-016 страница 36 Скачать руководство пользователя

Страница: 36 / 44

5-10

Operation

Safety information

Keep the installation and operating instructions together with the vehicle

documents.

Arrange for any irregularities to be examined by a workshop.

The driving aid will restrict the space available on the driver’s side to a cer-

tain extent once installed. Installing the driving aid alters vehicle operation.

When lending the vehicle to another person or when taking it to the workshop,

please ensure that you make them aware of the driving aid and tell the respective

person how to operate it.

Only personnel authorised by us may open the control, otherwise any

warranty claim shall be invalidated.

Should the vehicle enter emergency mode during operation, please notify the

workshop of the pedal system that has been installed and hand over all the doc-

umentation that goes with it. The responsible repair shop should contact the

system manufacturer in case of any doubt.

(For details of the Veigel GmbH + Co. KG hotline, see page 1-3.)

Causes of faults

After switching on the ignition, the

status LED does not flash for 6 s

or the accelerator pedal cannot be

changed.

Check and replace the fuses.

Malfunction

Action

Accelerator pedals/Veigel hand

accelerator not accelerating.

Accelerator module/Veigel hand accel-

erator defective; contact a specialist

workshop.

Содержание BHA23-016













































Результаты поиска

Содержание BHA23-016

Отзывы:

Похожие инструкции для BHA23-016

Бренды по названию

Популярные бренды

Veigel BHA23-016, Инструкция по установке и эксплуатации

Результаты поиска

Содержание BHA23-016

Отзывы:

Похожие инструкции для BHA23-016

Бренды по названию

Популярные бренды