Vega VEGAPULS 56K Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 72

background image

30

VEGAPULS 56K

,,

,,

,,

,,

,,

,,

,,

,,

,,

,,

,,

,,

,,

,,

,,

,,

,,

,,

,,

Measuring range (operating range) and max. measuring distance
Note: The use of the sensors in solid applications is restricted.

full

Meas. range

max. meas. distance 20␣ m

4 Mounting and installation

4.1 General installation instructions

Measuring range

The reference pane for the measuring range of
the sensors is the flange face. The measuring
range is 0␣ …␣ 20␣ m. For measurements in surge
or bypass pipes (pipe antenna) the max.
meas. distance is reduced (see "Technical
data - Measuring range“).

Please note that for measurements where the
measured product reaches the sensor flange,
build-up on the antenna is possible which can
cause measurement errors.

Reference pane

empty

Profiles with smooth interfering surfaces cause large
false signals

Round profiles diffuse the radar signals

A deflector causes signal scattering

Mounting and installation

False reflections

Flat obstructions and struts cause large false
reflections. They reflect the radar signal with
high amplitude.

Round profile interfering surfaces have a
diffuse reflection of the radar signals and
cause false reflections with low density. Hence
they are less critical than reflections from flat
surfaces.

If flat obstructions in the range of the radar
signals cannot be avoided, it is recommended
to reflect the interfering signals with a
deflector. Due to this scattering the interfering
signals will be low in amplitude and diffuse so
that they can be filtered out by the sensor.

min.
meas.
distance

min.

min. meas.
distance

min. meas.
distance

full

empty

«
...
28
29
30
31
32
...
»

Содержание VEGAPULS 56K









































































Отзывы:

Нет отзывов

Похожие инструкции для VEGAPULS 56K

Бренд: Yamaha Страницы: 69

Бренд: Cannon Страницы: 64

Бренд: Cannon Страницы: 73

Бренд: Hameg Страницы: 44

Бренд: Hameg Страницы: 60

Бренд: Hameg Страницы: 28

Бренд: HAMAR LASER Страницы: 113

Electone B-20CR

Бренд: Yamaha Страницы: 16

Бренд: Topcon Страницы: 62

Бренд: Hanna Instruments Страницы: 28

Бренд: Energometrika Страницы: 39

Бренд: Cecomp Страницы: 4

Бренд: Ratek Страницы: 25

Бренд: Caen Страницы: 63

Бренд: Caen Страницы: 35

Бренд: E Instruments Страницы: 2

Бренд: Ratek Страницы: 24

Бренд: Amptec Research Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды