background image

8

3 Mounting

FIBERTRAC 31 • Four-wire 4 … 20 mA/HART

62067-EN-211203

3 Mounting

3.1  General instructions

The source container is part of the measuring system. In case the 

source container is already equipped with an active isotope, the 

source container must be locked before mounting.
Danger:

Before mounting; make sure that the source is securely closed. Use 

a padlock to secure the source container in the closed condition and 

prevent it from being inadvertently opened.

Protect your instrument against moisture ingress through the following 

measures:

• 

Use a suitable connection cable (see chapter " 

Connecting to 

power supply

") 

• 

Tighten the cable gland or plug connector

• 

Lead the connection cable downward in front of the cable entry or 

plug connector

This applies mainly to outdoor installations, in areas where high 

humidity is expected (e.g. through cleaning processes) and on cooled 

or heated vessels.
Note:

Make sure that during installation or maintenance no moisture or dirt 

can get inside the instrument.
To maintain the housing protection, make sure that the housing lid is 

closed during operation and locked, if necessary.

Note:

For safety reasons, the instrument must only be operated within the 

permissible process conditions. You can find detailed information on 

the process conditions in chapter " 

Technical data

" of the operating 

instructions or on the type label. 
Hence make sure before mounting that all parts of the instrument ex-

posed to the process are suitable for the existing process conditions.
These are mainly:

• 

Active measuring component

• 

Process fitting

• 

Process seal

Process conditions in particular are:

• 

Process pressure

• 

Process temperature

• 

Chemical properties of the medium

• 

Abrasion and mechanical influences

Switch off source

Protection against mois-

ture

Process conditions

Содержание FIBERTRAC 31





























Отзывы: