VeEX VePAL TX300M Скачать руководство пользователя страница 277

Страница: 277 / 421

Like MX Discover, OAM Discover can also be used to discover far-end test units without manually configuring the local or remote

unit's destination address. If OAM is enabled on the TX300/e, any link partner that supports the IEEE 802.3ah protocol will be

discovered automatically and displayed under the

OAM Discover

tab. To access OAM Discover:

Go to

Throughput

OAM

Link

and tap on the 802.3ah check box to activate Link OAM. Select Active from the

OAM Mode

drop-down menu (only Active mode can send loop commands).

Tap on the

Control

button and select OAM Discover tab to see a list of discovered OAM devices. Select an OAM device and

press

Loop Up

to send a loop up command to the selected remote unit.

For detailed descriptions of Discovery Capabilities, Link Events, and Notification Settings, please see

15.6 Ethernet OAM Testing

Activating 802.3ah Link OAM

Go back to top

Go back to TOC

15.1.5 ViPAG Router Test

The ViPAG function tests end-to-end routed testing for 1G and 10G interfaces. To access ViPAG Router testing:

Select

Ethernet Test Mode

from the

Test Port Selection

screen, accessed by pressing the

Test Mode icon

the lower-right side of the screen

Make sure that the 10GE Port is connected to the router 10GE interface and that the 1 GE Fiber Port 2 is connected to the

router 1000Base-X or 10/100/1000Base-T interface
Press the ViPAG icon

Two test selections are available on the unit:

Router Wrap Test:

"On local unit" testing on a single unit

End-to-End Test:

"With remote test unit" testing

Controller: Carries out the peer-to-peer/asymmetric handshaking, loads the remote profile to the remote unit, and

initiates the test

Responder: Establishes IP connectivity and waits for the controller to connect/initiate the test

Go back to top

Go back to TOC

ViPAG Setup

Step 1: Quick Test Setup

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды