VeEX VePAL TX300M Скачать руководство пользователя страница 269

Страница: 269 / 421

Port setup or test interface configuration are accessed via the Setup menu located on the Home page. The available configuration

settings depend on the interface selected in the Test Mode selection.

The user selects the operation mode and the interfaces that will be used to carry out tests. Once the operating mode and interfaces

are selected, the user can independently configure the auto-negotiation, speed, duplex, and flow control settings for each port (where

applicable).

1 GE Fiber Port Setup

Go back to top

Go back to TOC

1 GE Fiber Port

Auto Negotiation:

On or Off. Matches the test set's negotiation settings to those of the link partner

Speed:

Default set to 1000 Mbps

Duplex:

Default set to Full

Flow Control:

TX On, RX On, Both On, or Off

When flow control is enabled, the test set will respond to pause frames received by the link partner by adjusting the

transmit rate

When flow control is disabled, the test set ignores all incoming pause frames from the link partner and continues

transmitting at the configured transmit rate

1 GE Copper Port Setup

Go back to top

Go back to TOC

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды