VeEX VePAL TX300M Скачать руководство пользователя страница 239

Страница: 239 / 421

E1 and DS1 ISDN PRI offer identical test options. DS1 ISDN PRI instructions are discussed in

11.7 E1 ISDN PRI

Go back to top

Go back to TOC

12.8 DS1 VF Tasks

The VF Tasks menu performs a variety of talk/listen functions.

DS1 VF Tasks Setup

Note:

Do not attempt to enter VF Tasks if the Frame LED is not green. Green LEDs indicate that the framing found on the

received signal matches the framing selected in the Setup screen. It is impossible to talk, listen, or perform other channelized

functions in the absence of frame synchronization, since channels can be identified only within a framed signal.

The VF Tasks screen features the following options:

Setup:

Tx and Rx T/S:

Input the number of channels (1-24) to test for transmitting and receiving time slots.

Mode:

Talk or send a tone on the transmit signal. Transmit audio data from the external headset into the selected

timeslot.

Code:

Select u-Law or A-Law.

Transmitted Frequency:

Input a frequency to transmit from 50 to 3950 Hz.

Transmitted Level:

Input a frequency to transmit from -60 to 3dBm.

ABCD:

Options are ON-HOOK, OFF-HOOK, WINK, or User (Manually set). Change the signalling bits transmitted with the

associated transmit channel. In SF-D4 framing these will be A/B and ESF framing will place that signal onto the A/B/C/D

position.

Programmable ABCD:

Manual (User) or IDLE, SEIZE.

Results:

Measure signal frequency and level in selected timeslot

Listen to the voice channel in selected timeslot via external headset

ABCD:

View the received Channel Associated Signalling System(CAS) bits

Data:

View the live 8-bit channel data as it is received from the selected channel

ABCD bits monitor and view data in selected T/S channel

Go back to top

Go back to TOC

12.9 Jitter and Wander

For more information on Jitter and Wander, please see

13.0 Jitter and Wander Application

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды