VeEX VePAL TX300M Скачать руководство пользователя страница 207

Страница: 207 / 421

APS Test Procedure:

The TX300/e should be connected to a tributary port of network element or transmission system to ensure that the

switching time is measured for the service transported by the SONET network.

Ensure that no errors or alarms are present on the transmission system because this will impact the measurement.

The measurement will be triggered by an Alarm Indication Signal (AIS)

The TX300/e measures how long the AIS event remains present after the event is first recognized and will continue to

measure the total disruption time in the event of multiple disruptions.

Go back to top

Go back to TOC

10.2.7.2 APS Sequence

The associated K1/K2 sequence and received K1/K2 bytes may be captured.

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды