manualshive.com logo in svg

VeEX VePAL TX300M, Руководство пользователя

VeEX VePAL TX300M - это мощный инструмент для тестирования сетей связи. Для того чтобы ознакомиться с возможностями прибора, загрузите бесплатное руководство по эксплуатации с manualshive.com. Подробная инструкция поможет вам максимально эффективно использовать данное устройство.

Поделиться
Скачать
background image

To access the Ethernet port, remove the protective rubber cover on the right hand side of the unit to expose the connector. Ethernet applications

include:

IP connectivity testing

Net Wiz testing

WiFi Wiz testing

Voice over IP (VoIP) testing

IPTV testing

Transfer measurement results and test profiles between the instrument and a computer using ReVeal TX software

Upload/download channel tables between the instrument and a computer using ReVeal TX software

Upgrade the instrument software using ReVeal TX software

Remote control of the instrument using ReVeal TX software (optional)

USB Port

To access the USB port, remove the protective rubber cover on the left hand side of the unit to expose the connector. The USB port supports:

Memory drives

WiFi adaptor for WiFi testing application

Go back to top

 

Go back to TOC

4.6 LEDs

The TX300 units are equipped with the following LEDs:

Fixed LED:

 A single LED indicates the power state of the unit.

The LED is off when the unit is powered off

The LED is green when the unit is powered on

The LED is orange when the unit is connected to the AC Mains and powered

off 

Soft LEDs:

 The Graphical User Interface (GUI) supports several "soft" LED functions

depending on test mode

Signal LED:

 Indicates presence of a valid input signal

Frame LED:

 Indicates presence of valid framing on the input signal

Pattern LED:

 Indicates test pattern synchronization in BERT, RFC and

Throughput modes

Alarm / Error LED:

 Indicates the presence of alarms or errors

Note:

 Each soft LED is equipped with a History function

Green LED:

 Indicates that no alarm/error has occurred

Red LED:

 Indicates that at least one alarm/error has occurred during the test

Red flashing LED:

 Indicates any alarms/errors that have occurred

Soft LED Functions

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для VePAL TX300M

Tanco A Series Operator'S Handbook Manual preview
A Series
Бренд: Tanco Страницы: 72
HABYS Aero Instruction Manual & Warranty preview
Aero
Бренд: HABYS Страницы: 16
Acterna A Series Operating Manual preview
A Series
Бренд: Acterna Страницы: 72
ICS Schneider Messtechnik HT10 User Manual preview
HT10
Бренд: ICS Schneider Messtechnik Страницы: 124
GBC AIO Quick Start Manual preview
AIO
Бренд: GBC Страницы: 8
KAPSCH T600 Operator And Maintenance Manual preview
T600
Бренд: KAPSCH Страницы: 57
Parr Instrument 4560 Operating Instructions Manual preview
4560
Бренд: Parr Instrument Страницы: 24
JBL 7130 Installation And Service Manual preview
7130
Бренд: JBL Страницы: 15
Cameo SCUBA User Manual preview
SCUBA
Бренд: Cameo Страницы: 64
Cameo OPUS Series User Manual preview
OPUS Series
Бренд: Cameo Страницы: 100
CAME PXTS4.3 Installer Manual preview
PXTS4.3
Бренд: CAME Страницы: 32
Gaspardo PA2 Use And Maintenance preview
PA2
Бренд: Gaspardo Страницы: 196
RAB X34 Installation preview
X34
Бренд: RAB Страницы: 2
JBL Synthesis SDEC-3000 Calibration Manual preview
Synthesis SDEC-3000
Бренд: JBL Страницы: 24
Xilica Audio Design XP series User Manual preview
XP series
Бренд: Xilica Audio Design Страницы: 30
Rane Four User Manual preview
Four
Бренд: Rane Страницы: 38
Kartsana BRAVA Instruction Manual preview
BRAVA
Бренд: Kartsana Страницы: 36
Kannad INTEGRA ARINC e-NAV Installation & Operation Manual preview
INTEGRA ARINC e-NAV
Бренд: Kannad Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды