VeEX VePAL TX300M Скачать руководство пользователя страница 19

Страница: 19 / 421

TX300M Test Ports

4.5.2 RJ-45 Interface (TX300e only)

Balanced, Tx and Rx electrical interfaces for T1 and E1 signals. The port is 120 ohm for E1 signals and 100 ohm for T1 signals.

Go back to top

Go back to TOC

4.5.3 Bantam Interface (TX300, TX300S and TX300M only)

Balanced, Tx and Rx interfaces for DS1 and E1 signals.

Go back to top

Go back to TOC

4.5.4 BNC Interface

Unbalanced, 75 ohm Tx and Rx interfaces for DS3 and E1, E2, E3, E4 and STM-0/STS-1 (51M), STS-3/STM-1E.

Go back to top

Go back to TOC

4.5.5 XFP/SFP Transceiver Interface

Optical Transceivers (Tx/Rx) conforming to Multi Source Agreement (MSA) recommendations are supported. Various SFPs are available for different

wavelengths and dynamic range requirements. Check the ordering options for more details. The standard optical connector type used on SFP

transceivers is LC. Please use appropriate low reflectance patchcords (Ultra Physical Contact [UPC]) and note the damage level associated with each

Transceiver. Customers opting to use or provide their own SFPs should ensure that the transceivers are multi-rate and that digital diagnostics are

supported – this enables the optical power and other measurements when in SDH optical test mode. Furthermore, only SFPs with low jitter and good

optical extinction ratio should be used. To comply with ROHS and other local government requirements, only compliant SFP transceivers should be

used.

Go back to top

Go back to TOC

4.5.6 SMA Interface

Unbalanced, NRZ electrical clock input

For DS1/T1: 1.544Mbps or 1.544 MHz

For E1: 2.048Mbps or 2.048MHz

Go back to top

Go back to TOC

4.5.7 Utility Ports

The Ethernet and USB ports are located on the left and right side of the unit.

RJ45, 10/100Base-T Port

TX300S_e-manual_D07-00-064P_RevA00

Содержание VePAL TX300M






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды

VeEX VePAL TX300M, Руководство пользователя

Результаты поиска

Содержание VePAL TX300M

Отзывы:

Похожие инструкции для VePAL TX300M

Бренды по названию

Популярные бренды