VeEX VePAL TX300 Скачать руководство пользователя страница 328

Страница: 328 / 421

V-SAM Setup - Services - PBB Settings

15.4.1.2 Service Attributes

Bandwidth Profile Parameters

The Bandwidth Profile specifies how much traffic the customer is authorized to transmit and how the frames are prioritized within

the network. In the Bandwidth table, the user specifies the following bandwidth criteria:

CIR:

Committed Information Rate. This is the guaranteed maximum rate at which the customer can send frames that are

assured to be forwarded through the network without being dropped. Tap on the box to enter a rate and choose between

IR Mbps

ULR Mbps

. Allowed values range from 0.01Mbps to the line bandwidth.

Information Rate (IR):

Measures the average Ethernet frame rate starting at the MAC address field and ending at

the CRC.

Utilized Line Rate (ULR):

Measures the average Ethernet frame rate starting with the overhead and ending at the

CRC.

V-SAM Services - Header

Excess Information Rate (EIR):

Maximum rate above the CIR at which the customer can send frames that will be

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Бренды по названию

Популярные бренды