VeEX VePAL TX300 Скачать руководство пользователя страница 21

Страница: 21 / 421

Go back to top

Go back to TOC

4.6 LEDs

The TX300/e is equipped with the following LEDs:

Fixed LED:

A single LED indicates the power state of the unit.

The LED is off when the unit is powered off

The LED is green when the unit is powered on

The LED is orange when the unit is connected to the AC Mains and powered

off

Soft LEDs:

The Graphical User Interface (GUI) supports several "soft" LED functions

depending on test mode

Signal LED:

Indicates presence of a valid input signal

Frame LED:

Indicates presence of valid framing on the input signal

Pattern LED:

Indicates test pattern synchronization in BERT, RFC and

Throughput modes

Alarm / Error LED:

Indicates the presence of alarms or errors

Note:

Each soft LED is equipped with a History function

Green LED:

Indicates that no alarm/error has occurred

Red LED:

Indicates that at least one alarm/error has occurred during the test

Red flashing LED:

Indicates any alarms/errors that have occurred

Grey LED:

Indicates no condition or a test that has not begun yet

Note:

The

History

key

on the rubber keypad resets the soft LEDs on the GUI

Soft LED Functions

Go back to top

Go back to TOC

4.7 Software Upgrade

There are two methods of updating the test set software: via USB port or ReVeal MTX300 software.

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды