VeEX VePAL TX300 Скачать руководство пользователя страница 20

Страница: 20 / 421

Balanced, Tx and Rx electrical interfaces for T1 and E1 signals. The port is 120 ohm for E1 signals and 100 ohm for T1 signals.

Go back to top

Go back to TOC

4.5.3 Bantam Interface (TX300 only)

Balanced, Tx and Rx interfaces for DS1 and E1 signals.

Go back to top

Go back to TOC

4.5.4 BNC Interface

Unbalanced, 75 ohm Tx and Rx interfaces for DS3 and E1, E2, E3, E4 and STM-0/STS-1 (51M), STS-3/STM-1E.

Go back to top

Go back to TOC

4.5.5 XFP/SFP Transceiver Interface

Optical Transceivers (Tx/Rx) conforming to Multi Source Agreement (MSA) recommendations are supported. Various SFPs are

available for different wavelengths and dynamic range requirements. Check the ordering options for more details. The standard

optical connector type used on SFP transceivers is LC. Please use appropriate low reflectance patchcords (Ultra Physical Contact

[UPC]) and note the damage level associated with each Transceiver. Customers opting to use or provide their own SFPs should

ensure that the transceivers are multi-rate and that digital diagnostics are supported – this enables the optical power and other

measurements when in SDH optical test mode. Furthermore, only SFPs with low jitter and good optical extinction ratio should be

used. To comply with ROHS and other local government requirements, only compliant SFP transceivers should be used.

Go back to top

Go back to TOC

4.5.6 SMA Interface

Unbalanced, NRZ electrical clock input

For DS1/T1: 1.544Mbps or 1.544 MHz

For E1: 2.048Mbps or 2.048MHz

Go back to top

Go back to TOC

4.5.7 Utility Ports

The Ethernet and USB ports are located on the left and right side of the unit.

RJ45, 10/100Base-T Port

To access the Ethernet port, remove the protective rubber cover on the right hand side of the unit to expose the connector.

Ethernet applications include:

IP connectivity testing

Net Wiz testing

WiFi Wiz testing

Voice over IP (VoIP) testing

IPTV testing

Transfer measurement results and test profiles between the instrument and a computer using ReVeal TX software

Upload/download channel tables between the instrument and a computer using ReVeal TX software

Upgrade the instrument software using ReVeal TX software

Remote control of the instrument using ReVeal TX software (optional)

USB Port

To access the USB port, remove the protective rubber cover on the left hand side of the unit to expose the connector. The USB

port supports:

Memory drives

WiFi adaptor for WiFi testing application

TX300/e_e-manual_D07-00-033P_RevG00

Содержание VePAL TX300






































































































































































































































































































































































































































Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды

VeEX VePAL TX300, Руководство пользователя

Результаты поиска

Содержание VePAL TX300

Отзывы:

Похожие инструкции для VePAL TX300

Бренды по названию

Популярные бренды