background image

At any customer location after the OLT and splitter, the FX120 will display 1490nm and 1310nm signal level values for GPON, 1577nm and 1270nm for

XGS-PON, and 1550nm for RF/CATV. ODN Loss is the difference between the transmitting signal from the OLT (TX) and the DS signal level measured at

the FX120 location.

If the OLT is not broadcasting its output power, the span loss value cannot be calculated.

Green, yellow, and red table colors indicate whether signal levels pass or fail against ITU-T G.984 standard threshold values configured in Setup. Refer to

Test and Profile Settings 

for information on test profile setup.

            

Green: 

The measured signal is above the critical threshold.

            

Yellow: 

The measured signal is below marginal and above critical.

             

Red: 

The measured signal level is below the critical threshold and does not meet the specification.

Upstream/Downstream/TC-Sync Signal Status

For more information, refer to 

Signal and Synchronization Status

.

Test and Profile Settings

Setup: 

Setup Test profile

Advanced: 

Leads to the Advanced Setup, Results, PLOAM and OMCI Decoder, and Active ONU

list.

Go back to top

 

Go back to TOC

6.0.2 Signal and Synchronization Status

The Status table displays detected 1490nm/1577nm downstream, 1310nm/1270nm upstream, and TC-Sync status.

GPON Signal and Synchronization Status Table

XGS-PON Signal and Synchronization Status Table

Status Table

1490nm/1310nm: 

If OK is displayed, light in the downstream 1490nm or upstream 1310nm direction is detected.

1577nm/1270nm: 

If OK is displayed, light in the downstream 1577nm or upstream 1270nm direction is detected.

Transmission Connectivity Sync (TC-Sync): 

OK UL/DL indicates that the FX120 is properly synchronized with the OLT and ONU/ONT traffic. No

UL/DL indicates the OLT and ONU/ONT are not synchronized properly. Consult VeEX technical support if unable to achieve TC-Sync.

OK indicates US or DS light is detected, but does not indicate whether ITU-T Threshold values are

met or if the OLT and ONU/ONT are properly synchronized.

LED Status

Upstream/Downstream LED Status

FX120_User_Manual_RevA02

Page 15 of 32

Содержание FX120

































Отзывы: