background image

Setup and Test

Testing the Overfill Alarm with the Console

10

Testing Overfill Alarm W/o Acknowledgment Switch

1. Reapply power. If the Overfill Alarm was wired properly, the alarm horn will sound immediately followed by the 

red alarm light flashing.

2. Turn Off power to the console and to the Overfill Alarm. Remove the test jumper between the Output Relay 

connections. 

Testing Overfill Alarm With Acknowledgment Switch

1. Turn power Off to the console and the Overfill Alarm. Put a jumper between the two Overfill Alarm relay 

connections in the console (see Figure

 

6).

2. Stand by the Acknowledgment Switch and have someone reapply power to the console and Overfill Alarm. If 

the Overfill Alarm was wired properly, the alarm horn will sound immediately followed by the red alarm light 

flashing.

3. Press the RESET button on the front of the Acknowledgment Switch. The alarm horn and red flashing light 

should shut off. The ACKNOWLEDGED light on the front of the switch should be On. (Pressing the RESET 

button shuts Off the alarms but does not clear the alarm. The cause of the alarm must be removed before the 

ACKNOWLEDGED light will turn Off.)

4. Turn Off power to the console and to the Overfill Alarm. Remove the test jumper between the console’s 

Output Relay connections.

5. Reapply power to the console and to the Overfill Alarm. The ACKNOWLEDGED light should now be Off 

because the cause of the alarm (in this case, the test jumper) has been removed.

Содержание Overfill Alarm















Отзывы: