ServerCall Paging System
VeDoSign
Nolenslaan 8, 3741 VT Baarn, Tel. +31 (0)35 543 07 38, Fax +31 (0)35 543 57 56, [email protected]
Innovatieve communicatie oplossingen en advies voor hospitality gerelateerde toepassingen -
www.vedosign.com
Manual
1. TRANSMITTER BRACKET
INSTALLATION
•
To page a pager with a single vibe
Press the corresponding number until
the unit beeps once and the green light
comes on. Pager will vibrate once and
the red LED light on top will turn fl ash
when it receives the page.
•
To page a pager with a dual vibe
Press the x2 button once and then press
the corresponding server/pager number
within 5 seconds. Pager will vibrate
twice and the red LED light on top will
fl ash when it receives the page.
•
To page a pager with a triple vibe
Press the x3 button once and then press
the corresponding server/pager number
within 5 seconds. Pager will vibrate
3 times and the red LED light on top
will fl ash when it receives the page.
•
Re-page feature
You may select to have this system page
the server one time only or repage them
3 times if the food has not been picked
up. (See programming instructions.)
The system can also notify the manager
on an optional digital pager with the
tardy server’s pager number.
•
To cancel a page
Press the corresponding number on the
transmitter (or cancel panel) until it
beeps once and the light goes off. If you
do not cancel the page, and the repage
feature is turned on, the pager will repage
the server 3 more times automatically
every 60 seconds (this feature is adjus-
table). The transmitter will change from
green (food up for 1 min.) to yellow
(food up for 2 min.s) to red (food up for
3 min.s) and fl ashing red (food dying in
the window!). At that point the system
can page the manager’s pager with the
server number notifying him that there
is food up in need of attention.
•
To page all server pagers
Press and hold the All Page button until
it stops fl ashing (5 seconds) and you
hear a single short tone. All pagers will
vibrate 4 times.
•
To page all manager pagers
Press and hold the mGR All button until
it stops fl ashing (5 seconds) and you
hear a single short tone. This function
only works if you have purchased the
optional manager display pager.
2. ADDITIONAL AND/OR
CANCEL PANEL
The ServerCall has the option of an ad-
ditional/cancel panel. The second panel
is plugged into the fi rst and placed in
another location. This second panel
allows you to send a page or cancel a
page from either unit. This can be espe-
cially useful when using an expeditor
system or when you need to send pages
from different parts of the kitchen. The
second panel receives power from the
main unit and does not require an ex-
ternal power source.
The main unit houses the transmitter
and power supply. Simply mount both
units in their desired location. Distance
can be anywhere from 1 foot to 150 feet
apart. (The standard patch cord is 6
feet long. Additional length is available
for an extra charge.) Plug in the power
supply to the main unit, plug the patch
cord from the side of the main terminal
to the side of the additional terminal
and you’re ready to go.
3. SYSTEM PROGRAMMING
To enter programming mode, press the
“
SET UP
” button and enter the
password “
1379
” followed by “
Enter
”.
If the password is accepted, the display
will show “
Menu Options
”. Use the “
2X
”
or “
3X
” key to scroll through the diffe-
rent menu options or press “
CANCEL
” to
exit the system programming menu.
(NOTE: For “
0
” use the “
10
” key).
1. Set the Current Time
• Press the “
ENTER
” key to go to “
Set
Current Time
” confi guration menu.
• At the “
Set Current Time
” menu,
set the hour (1 through 12) then
press the “
ENTER
” key.
• Set the min.s and press the “
ENTER
” key.
• Use the “
2X
” or “
3X
” key to select
Am or Pm.
• After the correct time is set, press the
“E
NTER
” key to return to the main menu
or press the “
CANCEL
” key 2 times to
exit the system programming menu.
Server Paging System – with CrystalCall® Pagers v909
