Quick Start - Marquee 8520 Ultra
VDCDS Doc#: 790200101 / Revision 001
Remote Control Layout and Controls
SOURCE
1
2
3
RECALL
HELP
POWER
6
9
5
8
4
7
0
MUTE
STBY
PROJ
UTIL
PIC
GEOM
CONV
EXIT
DETAIL
VOL
TINT
BRITE
COLOR
CONT
ENTER
*
#
Picture Menu
Utilities Menu
Display Controls
Projector
Status Page
Geometry Menu
Convergence Menu
Exit
Source
Recall
Help
# Test Pattern
Mute
Numeric Keys
Enter
To adjust or set:
Phase
Size
White Balance
Focus
Sync
Blanking
Clamping
Retrace
Decoder Options
To access the following utilities:
Source Setup
Channel List
Memories Display
Preferences
To adjust:
Color
Tint
Detail
Contrast
Brightness
Volume
to command a single
projector in a multi-
projector system
to display status
pages
To adjust:
Size
Keystone
Side Pin
Top
Bottom
Bow
C Linearity
S Linearity
Skew
to adjust red, green and
blue convergence
to exit from a menu or
function
for input selection
for channel up/down selection
for source message display
to select a Recall Memory
to go back one screen during
menu/help display
to view hidden slide bars
when message display is turned off
for context sensitive help
for setup guides
to select a test pattern
for display
Power
to turn the projector on or off
Standby
to turn both picture and
audio on or off
to turn audio on or off
to turn menus on or off
for menu item selection
for number entry
to select a highlighted
menu item
to select a dialog box
option
Arrow Keys
for adjustments
for menu item selection
for movement between
edit fields
Remote Options
Clock/Events
Service
Display Systems
For Technical Assistance Please Contact:
VDCDS Technical Services: 321.784.4427 or [email protected]
QUICK START - MARQUEE™ 8520 Two-Piece Series
This document is intended to provide the necessary information to perform the initial assembly, test and quick setup of the
Marquee™ 8520 Two-Piece Series projectors. For complete detailed assembly and operating instructions, refer to the
Marquee™ 8520 Service Manual (VDCDS P/N: 71178-02) contained on the accompanying CD-ROM.
Note:
The 8520 projection system is shipped in two-
separate assemblies. Before any testing or operation
of the system can be accomplished, the Electronic
Chassis (
EC
) and the CRT Head Assembly (
HA
)
MUST be connected together. Refer to the inside
section (Figure 1 and Figure 2) DO NOT apply any
main power until both sections have been assembled
per this instruction sheet.
Step 1.
Once the EC and HA have been assembled
together, connect the AC power cord,
located in the lower-left side of the EC.
Note:
Input voltage must be between 90 –
264 VAC, 50/60 Hz.
Step 2.
Connect an External Source (Optional)
a) Connect a 3, 4 or 5 wire source to the
projector’s built-in RGB input-slot 1
(VIM). Ensure the source is on and properly connected.
GREEN
RED
BLUE
HOR/COMP
RGB and Sync Signals from Source
BNC
connectors
VERT
SYNC
Step 3.
Turn the Projector On
a) Hold down the [
POWER
] key on the keypad for about one second to turn the projector on.
Step 4.
Select Internal Test or External Source
a) Internal Test: Press [
#
] to display the first level test pattern. Press [
EXIT
] to return to the external
source if available.
b) Select the External Source: Press [
SOURCE
] [
0
] [
1
] to select the source connected to the Video Input
Module (RGB).
Step 5.
Adjust the Display: Guided Help provides several on-line tutorials which explains how to operate the
projector and assist you during the setup process.
a) Press [
HELP
] [
1
]
to select the Guided Source Setup tutorial.
90 - 264 VAC
50 - 60 Hz
