VCS VideoJet 10 Скачать руководство пользователя

Страница: 23 / 70

Installation

VideoJet 10

Command entry

After the connection has been established, call up the main menu.
Additional submenus and functions are called up using the
onscreen commands.

Switch local echo off so that values entered are not repeated.

Enter only one command at a time.

When a value is entered (e.g. IP address) recheck the charac-
ters entered and only then press the [ENTER] key to transmit the
value to the VideoJet 10.

IP address

To operate the VideoJet 10 on a network, an IP Address valid for
the network must be provided.

The following address has been preset at the factory:

Transmitter:

192.168.0.1

Receiver:

192.168.0.2

Start up the terminal programm, e.g. HyperTerminal.

Enter user name

service

. The main menu will be displayed.

Enter

to open the

menu.

The submenu for network configuration will be displayed.

Enter

. The current IP address will be displayed; you will be

required to enter a new IP address.

Enter the new IP address and press [ENTER]. The new IP address
will be displayed and is immediately valid.

Содержание VideoJet 10







































































Результаты поиска

Содержание VideoJet 10

Отзывы:

Похожие инструкции для VideoJet 10

Бренды по названию

Популярные бренды

VCS VideoJet 10, Руководство пользователя

Результаты поиска

Содержание VideoJet 10

Отзывы:

Похожие инструкции для VideoJet 10

Бренды по названию

Популярные бренды