Vatech A9 PHT-30CSS Скачать руководство пользователя страница 216

Страница: 216 / 244

Page

215

244

9.2.

vatech A9(PHT-30CSS) Command-List

Command

Remark

[SPM_PANO]

Command to enter PANOrama mode

[SPM_CEPH]

Command to enter CEPH mode

[SPM_ARCT]

Command to enter Arch-CT mode

[SPM_RET_]

Move to the shooting start position for each mode

(PANOrama, CEPH, CT)

[SPM_ERDY]

Exposure switch press-ready command

[SPM_ERDC]

Exposure switch press cancel command

[SPM_PCON]

Command to let capture S/W run

[SPM_PCOF]

Command that the exposure software has ended (Cancel

switch press-ready cancel fu laser off function)

[SPM_HV___0000]

Tube Voltage Setting Command (ex) 0600 = 60kVp

[SPM_HA___0000]

Tube Current Setting Command (ex) 0400 = 4mA

[SPM_LON_]

Laser on depending on the capture mode

[SPM_LOF_]

Turn off all lasers

[SPM_CPON]

sensor power on (Operation for each mode)

[SPM_CPOF]

sensor power oFF (Operation for each mode)

[SPM_CSON]

CT sensor power on (Independent of the current mode)

[SPM_CSOF]

CT sensor power off (Independent of the current mode)

[SPM_PSON]

PANOrama sensor power on (Independent of the current

mode)

[SPM_PSOF]

PANOrama sensor power off (Independent of the current

mode)

[SPM_HSON]

CEPH sensor power on (Independent of the current mode)

[SPM_HSOF]

CEPH sensor power off (Independent of the current mode)

[SPM_PVER]

Know your motherboard firmware version (must be used

when the device is down. Transmission during operation may

cause equipment malfunction.)

[SPM_IVER]

Knowing the Firmware Version of the Inverter Board

[SPM_TVER]

Know the firmware version of the Main Board, Collimator

Board, Column Board, Inverter Board, MP3, Keypad

[SPM_TUTS]

Tube feedback test with exposing switch

[SPM_XTST_0000]

exposure time test. Input the command

[SPM_XTST_number] used for authentication
(Number is exposure time, 1 second = 0100, 10 seconds =

1000)

[SPM_XON_]

Turn on X-ray exposure

[SPM_XOF_]

Turn off X-ray exposure

[SPM_TMP?]

Tube temperature requirements

Содержание A9 PHT-30CSS





















































































































































































































































Результаты поиска

Содержание A9 PHT-30CSS

Отзывы:

Бренды по названию

Популярные бренды

Vatech A9 PHT-30CSS, Техническое руководство

Результаты поиска

Содержание A9 PHT-30CSS

Отзывы:

Бренды по названию

Популярные бренды