Varta 56650 764 098 Скачать руководство пользователя

Страница: 4 / 33

1 Caution/warning statements

1.1

General safety signs

Symbol

Meaning

Prohibition symbols are circular, showing a

black pictogram on a white background

surrounded by a red edge with a crossbar.

Warning signs are triangular, showing a black

symbol and edge on a yellow background.

Environmental regulations are information on

statutory requirements, which have to be

complied with, especially during disposal.

1.2

General hazard sources

If the following instructions for handling the device are not observed, this might lead to personal injury

or damage to the battery or your device, for which VARTA Storage GmbH will accept no liability.

a. Danger of electrical voltage

WARNING

Contact with electrical voltage!

Risk of fatal injury from electric shock!

Keep the module always sealed.

Pay attention to any damage of electrical

equipment! Eliminate defects immediately!

Don´t open the module.

Don’t connect the modules in serial only in
parallel.

Don´t connect the module or charger in reverse

polarity.

Содержание 56650 764 098


































Результаты поиска

Содержание 56650 764 098

Отзывы:

Похожие инструкции для 56650 764 098

Бренды по названию

Популярные бренды

Varta 56650 764 098, Техническое руководство

Результаты поиска

Содержание 56650 764 098

Отзывы:

Похожие инструкции для 56650 764 098

Бренды по названию

Популярные бренды