background image

 

POWX00425 

EN

 

Copyright © 2021 VARO 

P a g e

 | 

8

 

www.varo.com 

8.3 

To install or remove the battery pack 

8.3.1 

To remove the battery 

Press both the battery release buttons and gently pull the battery out of the drill. 

8.3.2 

To install the battery 

Hold the drill upright in one hand and the battery in your other hand. While pressing with two 
fingers on the battery release buttons, insert the battery until it clicks into place. Do not use 
excessive force when inserting the battery. If the battery does not slide in easily, it is not being 
inserted correctly. It is also possible that there could be damage to the battery, battery 
terminals or the drill. 

8.4 

Installing/removing bits and drills 

8.4.1 

Installing bits/drills 

Lock the switch trigger by placing the direction of rotation selector in centre position.  
Open or close chuck jaws to a point where the opening is slightly larger than the bit size you 
intend  to  use.  Also,  raise  the  front  of  the  drill  slightly  to  keep  the  bit  from  falling  out  of  the 
chuck  jaws. Insert  drill  bit  straight  into  chuck  the full  length  of  the  jaws  as shown  in. Tighten 
the chuck jaws on the drill bit.  
WARNING: Make sure to insert drill bit straight into chuck jaws. 
Do  not  insert  drill  bit  into  chuck  jaws  at  an  angle,  this could cause drill  bit  to  be  thrown  from 
drill resulting in possible serious personal injury or damage to the chuck.  

8.4.2 

Removing bits/drills 

Lock the switch trigger by placing rotation selector in centre position. 
Loosen the chuck jaws from the drill bit. 
Note: Rotate chuck body in the direction of the arrow marked. Release to loosen chuck jaws. 
Do not use a wrench to tighten or loosen the chuck jaws. 
Remove the drill bit from the chuck jaws. 

8.5 

General hints for drilling 

Always make sure that the torque adjustment ring is set to “drill” position. 

8.5.1 

Drilling in all materials 

Always use sharp drill bits. Mark the place where you would like the hole to be drilled. 
Commence with a slow speed to start the hole. Reduce your pressure on the drill when the 
drill bit is about to break through the material. 

8.5.2 

Metal drilling 

Support thin material with a piece of scrap wood. Use a center punch to mark the position of 
the hole. If drilling a large hole, use a small size drill bit first to establish a pilot hole then use 
the required large size drill bit. Use only HSS (High Speed Steel) drill bits or those 
recommended for metal use. When drilling into iron or steel, use no lubricant but withdraw the 
drill regularly to assist cooling. 

Содержание POWERPLUS POWX00425













Отзывы: