VARO POWERPLUS POWEG8012 Скачать руководство пользователя

Страница: 11 / 14

POWEG8012

P a g e

www.varo.com

▪

Fuel filter

▪

Fuel vent
plugged

▪

Contaminants
residues in
fuel

▪

Clean or
replace

▪

Spark plug

▪

Plug dirty
worm

▪

Normal wear

▪

Clean and
adjust or
replace

▪

Carburetor

▪

Improper
adjustment

▪

Excessive
dirt/debris

▪

Screen
cracked or
perforated

▪

Vibration

▪

Adjust

▪

Cooling
system

▪

Extended
operation in
dirt/dusty
locations

▪

Normal wear

▪

Clean

▪

Spark
arrestor
screen

▪

Replace

Engine
does not
crank

▪

N/A

▪

N/A

▪

Internal engine
problem

▪

See dealer

12 TECHNICAL DATA

model

POWEG8012

Engine

Air cooled 2 stroke engine

Cylinder content:

42,7 CC

Power:

1,25 kW

Tank content:

1,2 l

Mowing width threading head:

460 mm

Wire diameter:

2,4 mm

Cutting width knife

255 mm

Rotation speed grass trimmer

8000 min-1

Rotation speed brush cutter

8500 min-1

Spark plug

CDK

13 NOISE

Noise emission values measured according to relevant standard. (K=3)
Acoustic pressure level LpA

88 dB(A)

Acoustic power level LwA

110 dB(A)

ATTENTION! Wear hearing protection when sound pressure is over 85
dB(A)

aw (Vibration)

7,5 m/s²

K = 1,5 m/s²

14 TRANSPORTATION

▪

Turn off the motor during transportation of the tool.

▪

During transportation, the protection should be fastened around the blade.

▪

During transportation in a vehicle, the tool should be placed in such a way as to prevent
any fuel leakage.

▪

If your appliance is to be transported, the fuel tank must be completely emptied.

▪

When unloading your appliance from the vehicle after transportation, make sure that the
motor does not hit hard against the ground. This could cause severe damage to the fuel
tank.

Содержание POWERPLUS POWEG8012















Результаты поиска

Содержание POWERPLUS POWEG8012

Отзывы:

Похожие инструкции для POWERPLUS POWEG8012

Бренды по названию

Популярные бренды

VARO POWERPLUS POWEG8012, Руководство пользователя

Результаты поиска

Содержание POWERPLUS POWEG8012

Отзывы:

Похожие инструкции для POWERPLUS POWEG8012

Бренды по названию

Популярные бренды