background image

 

POWDP15630 

EN

 

Copyright © 2021 VARO 

P a g e

 | 

9

 

www.varo.com 

9.4 

Fitting and changing tools (Fig. 3) 

The device is equipped with a SDS-plus attachment system. 

 

Clean tools and grease with a thin layer of machine grease before fitting. 

 

Fit the desired bit into the bit holder.  

 

Push and rotate the dust-free tool into the tool holder as far as it will go. The tool will lock 
automatically. 

 

Check that it has locked by pulling the tool 

9.5 

Removing SDS-plus tool 

Pull back fastening sleeve, hold and remove tool. 

Accessories can be hot after use.  Don’t touch the tip of accessory by hand!  
Please always use protective gloves to remove accessories. 

9.6 

Switching ON/OFF 

 

Switching on: 

 Press the operating switch (5). 

 

Switching off: 

 Release the operating switch (5). 

Note: The trigger switch can be used as a variable speed control 
mechanism. 

9.6.1 

Switch lock (Fig. 4) 

The switch trigger can be locked in the centre position. 
This helps to reduce the possibility of accidental starting when not in use. To lock the switch 
trigger, place the direction of rotation selector in the centre position. 

9.6.2 

Direction of rotation (Fig. 5) 

Direction of rotation is controlled by the direction of rotation selector located above the switch 
trigger. 

9.6.2.1 

Clockwise rotation: 

Right: To select forward rotation, release the on/off switch and push the forward/reverse lever 
to the left side of the tool. 

9.6.2.2 

Anticlockwise rotation: 

Left: To select reverse rotation, push the lever to the right side of the tool. 

9.6.3 

Variable speed 

This tool has a variable speed switch that delivers higher speed and torque with increased 
trigger pressure. 
Speed is controlled by the amount of switch trigger depression. 

9.7 

Handle attachment (Fig. 6) 

For reasons of safety, only use the hammer drill with handle attachment. 
You will be able to obtain a safe body position when working by rotating the handle 
attachment. Loosen and turn the handle attachment in an ant-clockwise direction. Slip loop 
onto the neck of the housing tool and position the handle, then tighten the handle attachment. 

 

 

Содержание POWERPLUS POWDP15630














Отзывы: