background image

 

POWDP15600 

EN

 

Copyright © 2021 VARO 

P a g e

 | 

9

 

www.varo.com 

9.4 

Fitting and changing tools (Fig. 3) 

The device is equipped with a SDS-plus attachment system. 

 

Clean tools and grease with a thin layer of machine grease before fitting. 

 

Pull back fastening sleeve and hold. 

 

Push and rotate the dust-free tool into the tool holder as far as it will go. The tool will lock 
automatically. 

 

Check that it has locked by pulling the tool. 

9.5 

Removing SDS-plus tool 

Pull back fastening sleeve, hold and remove tool. 

Accessories can be hot after use.  Don’t touch the tip of accessory by hand!  
Please always use protective gloves to remove accessories. 

9.6 

Switching ON/OFF 

 

Switching on: 

 Press the operating switch (4). 

 

Switching off: 

 Release the operating switch (4). 

9.6.1 

Switch lock (Fig. 4) 

The switch trigger can be locked in the centre position. 
This helps to reduce the possibility of accidental starting when not in use. To lock the switch 
trigger, place the direction of rotation selector in the centre position. 

9.6.2 

Direction of rotation (Fig. 5) 

Direction of rotation is controlled by the direction of rotation selector located above the switch 
trigger. 

9.6.2.1 

Clockwise rotation: 

Right: To select forward rotation, release the on/off switch and push the forward/reverse lever 
to the left side of the tool. 

9.6.2.2 

Anticlockwise rotation: 

Left: To select reverse rotation, push the lever to the right side of the tool. 

9.6.3 

Variable speed 

This tool has a variable speed switch that delivers higher speed and torque with increased 
trigger pressure. 
Speed is controlled by the amount of switch trigger depression. 

9.7 

Dust collection device 

Before carrying out hammer-drilling work vertically overhead pull dust collecting device over 
the drill bit. 

 

 

Содержание POWDP15600













Отзывы: