background image

14

 
Värmebaronen MP4 G2 / MP6 G2

Menu - Advanced Service Level

Delivery setting

area

std

 

20.  

0

Upper temperature function, choice of method. 
Absolute value for upper temperature.

 

0 = absolute

 
 

1

20.  

Temperature relative to setpoint.

1 = relative

 

21.   10

Temperature level of the upper temperature function - setting  
This parameter is used regardless of the above selection. 
To be adjusted if an absolute value is selected for the upper temperature.

6 – 105°C

15°C

 

22.  

0

Frost protection - the choice of whether frost protection should be active or inactive. 
Frost protection inactive.

 

0 = off

 
 

1

22.  

1

Frost protection active.

1 = on

 

23.  

0

Manual tests  
Manual tests according to rows 24 - 26, disabled

 

0 = off

 
 

0

23.  

1

Manual tests according to rows 24 - 26, are possible. 
The function is deactivated automatically after 4 minutes.

1 = on for 4 

min

 

24   

0

Power connection. 
Connection can only be done after the function is activated in row 23.

 
 

0, 1 and 2

 
 

0

24   

1

Press + or - to select number of power stages. 
Manual connection is subordinate to all protection functions.

 

25.  

0

Circulation pump  
Connection can only be done after the function has been activated in row 23.

 

0 = off

 
 

0

25.  

1

Manual connection of the circulation pump. 
Press + or - to select.

1 = on

 

26.  

0

Buzzer alarm. 
Connection can only be done after the function is activated in row 23.

 

0 = off

 
 

0

26.  

1

Manual connection of buzzer alarm. 
Press + or - to select.

 

1 = on

27.   30

Display of the temperature of the power circuit board.
Temperature too high >55° C.

0 – 55°C

28.   --

Room unit and UTK function not selected.

28.   30

UTK room unit, P-factor, proportional impact, 0.1°C/°C.

Adjustment should only be performed by a person with an understanding 

of the impact!

0 – 100

30

29.   --

Room unit and UTK function not selected.

29.   10

UTK room unit. I-factor, I-part impact, 0.1°C/°C/h.

Adjustment should only be performed by a person with an understanding 

of the impact!

0 – 100

10

Enter 21 in the menu "Service level" row 19, for access to menu "Advanced Service Level"!

Advanced Service Level, rows 20-29, alternate between row number window and parameter value.

Содержание MP4 G2

























Отзывы: