Varian HS-20 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 43

Varian HS-20 Скачать руководство пользователя страница 29

Operation

2-2

a.

Switch off the power to the diffusion pump heaters.

b.

Admit cooling water to the quick-cool coil if necessary and continue to circulate it until the
pump body just above the boiler heat shield can be touched (approximately 130°F or 54°C).
In valved systems which have tight inlet and foreline connections, it is possible to close valves
to isolate the diffusion pump at inlet and discharge, to air-release the remainder of the sys-
tem, shut off the heat to the diffusion pump, and stop the mechanical pump. With this method,
the quick-cool coil does not have to be used. However, the water flow through the pump must
be maintained until the boiler cools down below approximately 300°F (150°C).

d.

Check inlet and forepressure performance by means of the system instrumentation.

e.

During operation, the gas load at the inlet of the diffusion pump should not exceed the maxi-
mum throughput capability of the pump. This means that the pressure at the inlet flange
should not (except in transient conditions) exceed approximately 1 x 10

-3

Torr (.133 Pa). Dur-

ing operation, the discharge or fore pressure must be below the specified tolerable forepres-
sure.

2-2

SHUTDOWN PROCEDURE

WARNING

_____________

Boiler temperatures reach 530°F (275°C) which can cause serious
burns when touched. Always ensure surfaces have cooled near room
temperature before touching them.

CAUTION

________

Do not operate the quick-cool coil when the pump is cold or out of ser-
vice to prevent harmful collection of condensation on the boiler plate,
heater, and heater terminals.

Air release or admitting air to a pump with a hot boiler, especially when it is under vacuum, permits a
strong oxidizer to contact the hot pump oil and thereby increases the risk of an explosion.

«
...
27
28
29
30
31
...
»

Содержание HS-20












































Отзывы:

Нет отзывов