Varian HS-20 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 43

Varian HS-20 Скачать руководство пользователя страница 13

CAUTION

________

Acetone, alcohol, and other solvents degrade O-ring materials reducing
their ability to hold a vacuum. Do not use acetone or other solvents on
O-rings. If necessary to clean O-rings, wipe with lint-free, clean cloth,
wash in detergent and water, or use a small amount of pump oil.

WARNING

_____________

If hazardous gas, vapors, chemicals, or combustible mixtures are
pumped, sufficient quantities may exist during operation. This pump
may contain decomposed and/or overheated pump oils or poisonous
and/or corrosive process materials which are highly toxic and also can
be an asphyxiant. Proper operation will not always ensure that all haz-
ardous materials have been removed.

WARNING

_____________

Hot oils can cause serious burns. Wear protective gloves and
long sleeved, loose fitting, heat resistant garments when draining
pump oil.

WARNING

_____________

When lifting some Varian diffusion pumps, use power-assisted equipment
and trained moving/installation personnel to avoid dropping, slipping,
and/or overturning the pump and severely injuring personnel. Check
weight of equipment before lifting and do not stand under equipment
being moved.

NOTE

________

Always dispose of used or dirty oil properly and in compliance with all
local, state, and federal environmental laws and regulations.

«
...
11
12
13
14
15
...
»

Содержание HS-20












































Отзывы:

Нет отзывов