Varec 2920 Скачать руководство пользователя страница 30

Страница: 30 / 194

2920 Float & Tape Transmitter

4 Wiring

Installation and Operations Manual

Communications Wiring

The following table describes the wiring considerations for each communications protocol.

Terminal / Function

Terminal

Assignment

Description

TB1 — DC Power &
Communications

B+

Positive Terminal - DC Power

All Boards

Bi-Phase Mark Communications
(Interchangeable - No polarity)

Bi-Phase Mark Interface

- TX1/ - RX (B)

EIA-485 MODBUS

Space

Mark/Space

Computer (RXD)

TankWay

Bi-Phase Mark Communications
(Interchangeable - No polarity)

Bi-Phase Mark Interface

+ TX1/ + RX (A)

EIA-485 MODBUS

Mark

Mark/Space

Encoder (TXD)

TankWay

B-

Negative Terminal - DC Power

All Boards

TB2 — Digital Input/
Temperature Input

RTD A

RTD Signal

All Boards

RTD B

RTD Return 1

RTD C

RTD Return 2

DI2

Digital Input 2

DI COM

Digital Input Common

DI1

Digital Input 1

TB3

See wiring diagrams for each order code on the following pages

TB4

GND

Earth Ground

All Boards

GND

TB5

HART+

Ex d HART+ (Non-I.S.)

All boards, unless I.S.
HART Master I/O option
selected, and then not
used.

HART-

Ex d HART- (Non-I.S.)

Display Interface

ALL Boards

Communications Protocol

Description

Bi-Phase Mark

Shielded, twisted pair of 18 AWG wire is
recommended. This option provides compatibility
with Enraf (Honeywell) Bi-Phase Mark Level
products. Cable capacitance is 1 microFared (1

maximum. Resistance is 200 Ohms per wire (400
Ohms per loop.)

Содержание 2920



































































































































































































Результаты поиска

Содержание 2920

Отзывы:

Varec 2920, Инструкция по установке и эксплуатации, Страница: 30 / 194

Результаты поиска

Содержание 2920

Отзывы: