Vanderbilt ACT365-ACU Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 18

Vanderbilt ACT365-ACU Скачать руководство пользователя страница 17

5 Door Controller Status Indicators

5.1 ACT365-ACU

Status indicators appear on the front of the ACT365-ACU Door Controller.

The meaning of each indicator is described below.

(A) Power / System Running

This indicates that the ACT365-ACU has power.

(B) Communications

Constant illumination indicates that the ACT365-ACU is connected to the ACT365 service.

Flashing indicates that there is an issue connecting to the ACT365 service.

(C) Fault

Illuminates to indicate a fault on the system.

Possible causes are:

l

Tamper open: ACT365-ACU housing is not closed.

l

Break Glass: ACT365-ACU Controllers provide a method to monitor an Emergency break glass switch
via the BG/EDR input. The fault LED will illuminate if the Emergency break glass switch is activated.

l

Mains Fault: ACT365-ACU will accept a mains present signal from a PSU. This is wired into AC MON
input on the PCB. When the PSU has no mains supply the fault is active.

l

Low Supply Voltage: When voltage to the +12/24V terminal is less than +9V.

l

Fuse Blown: The +12/24V output on the READER terminals is current limited to provide short circuit
protection. The Fault LED will illuminate if too much current is drawn from this connection.

l

The ACT365-ACU cannot connect to the ACT365 service.

5.2 ACT365-ACU2A and ACT365-ACUPoE

Fault indication

Mains present

© Vanderbilt 2019

17

A-100521-c

15.03.2019

«
...
15
16
17
18
»

Содержание ACT365-ACU



















Отзывы:

Нет отзывов