V&A M266 Series Скачать руководство пользователя страница 3

1. SAFETY INFORMATION 

  The meter is completely portable, LCD, 3 1/2 digit clamp meter with insulation test 
function (with option 500V insulation tester unit). It has been designed according to 
IEC61010 concerning electronic measuring instruments with an over-voltage category 
(CATIII) and pollution 2 and safety requirements for hand-held current clamps for electrical 
measurement and test. 
  Follow all safety and operating instructions to ensure that the meter is used safely and is 
kept in good operating condition. 

1.1  PRELIMINARY 

* When using this meter, the user must observe all normal safety rules concerning: 
  - Protection against the dangers of electronic current. 
  - Protection of the meter against misuse. 
* Full compliance with safety standards can be guaranteed only if used with test leads 
supplied. If necessary, they must be replaced with the same model or same electronic 
ratings. Measuring leads must be in good condition. 

1.2  DURING USE 

* Never exceed the protection limit values indicated in specifications for each range of 
measurement. 
* When the meter is linked to measurement circuit, do not touch unused terminals. 
* When the value scale to be measured is unknown beforehand, set the range selector at 
the highest position. 
* Before rotating the range selector to change function, disconnect test leads from the 
circuit under test. 
* When carrying out measurements on TV or switching power circuits, always remember 
that there may be high amplitude voltage pulses at test points which can damage the 
meter. 
* Never perform resistance measurements on live circuits.   
* Always be careful when working with voltage above 60V dc or 30V ac rms. Keep fingers 
behind the probe barriers while measuring. 
* When the jaw opening and to the conductor under test, your fingers must keep behind 
the barrier indicator .The barrier or tactile indicator shall warn the operator of the limit of 
safe access. 
* Never ground yourself when talking electrical measurement, do not touch exposed 
metal pipes, outlets, fixtures, etc., which might be at ground potential. Keep your body 
isolated from ground by using dry clothing, rubber shoes, or any approved insulating 

Содержание M266 Series













Отзывы: