Vanair 050518 Скачать руководство пользователя | Manualshive

Страница: 55 / 210

background image

AIR N ARC

®

300 SERIES ALL-IN-ONE POWER SYSTEM

®

SECTION 4: INSTALLATION

090012-OP_r0

PAGE - 37

WARNING

ELECTRICAL HAZARD! Be sure the

battery is disconnected before starting

the installation.

4.1 MACHINE PACKAGE RECEIPT/

INSPECTION

Upon receipt of the machine package, inspect the
exterior of the shipping crate for signs of shipping/transit
damage. Any damage should be reported immediately to
the shipping company. Open the lid and inspect the
component parts and supports to ensure that there has
been no internal movements of assemblies or
components which may have caused damage. To install
the Vac-Tron ADBD Compressor System, refer to the
following sections:

4.2 MACHINE PACKAGE PREP

Refer to

Figure 4-1, Installation and Dimensions

Diagram

, and the following instructions.

1. Remove packing and inspect the machine for

shipping damage.

2. Check fluid levels, if needed. Refer to

Section

6.6.3

for compressor oil, and

Section 6.6.12

for engine oil.

4.3 SERVICE BODY PREP

Consult

Section 3, Specifications

for dimension

requirements, and the following instructions.

System Component or

Part Group Task

Manual

Section

Location

Machine Package Prep

4.2

page 37

Service Body Prep

4.3

page 37

Machine Package Mounting

4.4

page 39

Installation and Dimensions Dia-
gram (Part 1 of 2)

4.5

page 42

Installation and Dimensions Dia-
gram (Part 2 of 2)

4.6

page 43

SECTION 4: INSTALLATION

DANGER

DO NOT install in enclosed spaces.

NOTE

Contact Vanair at

(219) 879-5100 / (800) 526-8817

Service Fax: (219) 879-5335

www.vanair.com

to report missing items, incorrect part

numbers, or other discrepancies.

NOTE

Install electrical components (circuit

breakers, pressure switches, toggle

switches, etc.) in locations where

exposure to water or moisture will be

most minimized.

NOTE

In order to prevent accidental damage to

vehicle components (fuel tanks, lines,

brake lines, wiring harnesses), note their

location before drilling any holes.

DANGER

Grounding must consist of a minimum

10 gauge wire between the instrument

panel, the machine, and the

truck chassis.

«
...
53
54
55
56
57
...
»

Содержание 050518



















































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 050518

Бренд: Quasar Страницы: 3

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Samlexpower Страницы: 24

Бренд: TP-Link Страницы: 59

Бренд: M7 Страницы: 14

PullzAll 885002

Бренд: Warn Industries Страницы: 49

Бренд: Wel-Bilt Страницы: 4

Бренд: Skil Страницы: 12

Бренд: RED ROOSTER Страницы: 8

Бренд: Novus Страницы: 22

Бренд: MasterCraft Страницы: 26

Бренд: Quantum Instruments Страницы: 9

Бренд: EKSMA OPTICS Страницы: 15

Бренд: Milwaukee Страницы: 28

Бренд: Makita Страницы: 68

SITOP PSU100L 6EP1332-1LB00

Бренд: Siemens Страницы: 58

Бренд: Whelen Engineering Company Страницы: 4

Бренд: Sealey Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды