Vanair 050518 Скачать руководство пользователя

Страница: 116 / 210

SECTION 6: MAINTENANCE

AIR N ARC

300 SERIES ALL-IN-ONE POWER SYSTEM

PAGE - 98

090012-OP_r0

6.6.15.4 REPLACING THE GENERATOR

SERPENTINE DRIVE BELT

To replace the generator serpentine belt consult

Figures

6-19

and

6-22

, and the following procedure:

1. With the machine off and the ignition key

removed, open and remove the front access
panel.

2. Locate the clutch retaining cable ([

] (in

Figure 6-19

) secured to the base floor of the

machine near the clutch apparatus of the
engine.

3. Unfasten the clutch retaining cable [

] (

Figure

6-19

) by removing the retaining cable bolt

[

], lock washer [

], and washer [

] securing

TOOLS NEEDED

REPLACEMENT

PART(S)

Wrench - Size 5/16” (for
Tensioner Bolt)

Serpentine Belt

No. DR62184

Tension Tester

Socket Wrench - Size 3/4”

KEY

DESCRIPTION

KEY

DESCRIPTION

IDLER SHEAVE

TENSIONER PLATE MOUNTING AND ADJUSTMENT BOLT:
Loosen bolt to allow tensioner plate to pivot manually to achieve
new belt-tensioned position.

TENSIONER PLATE

Belt tension adjustment should be verified using a tension tester.

Figure 6-21: Generator Belt Re-tensioning

NOTE

Vanair

recommends that the air

compressor and generator serpentine

belts both be changed at the same time

even if only one of the belts is in need of

being changed.

Содержание 050518



















































































































































































































Результаты поиска

Содержание 050518

Отзывы:

Похожие инструкции для 050518

Бренды по названию

Популярные бренды

Vanair 050518, Руководство по эксплуатации и список запасных частей

Результаты поиска

Содержание 050518

Отзывы:

Похожие инструкции для 050518

Бренды по названию

Популярные бренды