Valley VRI-iS Скачать руководство пользователя страница 75

Страница: 75 / 102

Troubleshooting

GPS Antenna Test

To test the GPS Antenna do the following:
1. At the control panel, turn the control panel dis-

connect to on.

2. Turn on Service Mode by pushing

Menu

Sys-

tem

Diagnostics

Service Mode

, and then

checking the

Service Mode

checkbox.

3. Start the computer and open Valmont Terminal.
4. Plug USB to serial adapter into computer. See

Figure 75-1.

5. At the GPS tower box, turn tower box disconnect

off and unplug RJ11 plug from the PLC board.

6. Plug the RJ11 plug into the GPS Antenna Tester

(03E3638). See Figure 75-1.

7. Plug the USB to serial adapter into the GPS An-

tenna Tester. See Figure 75-1.

8. Turn the GPS tower box disconnect to on. The

GPS tower box power supply ON indicator light
should be lit.

9. On the Valmont Terminal screen, select the Com

Port and set the baud rate to 4800.

10. Click Open Port.

• The GGA messages should start streaming

across the screen once every second or once
every four seconds depending on the type of
GPS antenna. See Figure 75-2.

03E3466 - 1 Second 19x Garmin

03E3467 - 4 Second 19x Garmin

• GPS lock on the satellites is indicated by the

number following “W” in the message.

0 = No GPS lock

1 = Standard GPS lock

2 = DGPS lock

• If no messages are seen:

Check all connections

Verify 12 VDC to the GPS antenna

Retest GPS antenna

Replace Antenna

• If message appears to be in a different format

other than what is shown in Figure 75-2, the
GPS antenna may not be programmed cor-
rectly and should be replaced.

Figure 75-1 1. GPS Tower Box

2.  RJ11 Plug
3.  PLC Board
4.  GPS Antenna

Tester (03E3638)

5. USB to Serial Adapter
6. Power Supply Indicator

Light

Figure 75-2 1. Com Port

2.  Baud Rate
3.  Open Port
4.  GPS Lock Indicator

Содержание VRI-iS







































































































Результаты поиска

Содержание VRI-iS

Отзывы:

Бренды по названию

Популярные бренды

Valley VRI-iS, Руководство по установке

Результаты поиска

Содержание VRI-iS

Отзывы:

Бренды по названию

Популярные бренды