Valley VRI-iS Скачать руководство пользователя

Страница: 57 / 102

Troubleshooting

System Error Codes

Listed below and on the next page are the VRI-iS and GPS related error codes. See Figures 57-1 and 58-1.

Error

Description

Threshold

Shut Down

Possible Causes

Corrective Actions

E16

VDC Communication
Error, Primary Communi-
cation Module

Each time a command message is
sent with no reply message being
received (VRI-iS or Encoder options
only).

Yes - if

Position Loss
Shut Down is

enabled.

Communications error to
Comm Board.

E17

VRI-iS Sprinkler Com-
munication Error
• The sprinkler ID

and number of oc-
currences for this
sprinkler are logged
with the error.

Each time a sprinkler fails to respond
to a Set Sprinkler command retry.

Communications error to
VRI-iS valve.

E18

GPS Communication
Error
• The Satellite Count

is logged with the
error.

When a transition occurs from GPS
communicating to GPS not communi-
cating.
GPS Position must be enabled.

Yes - if Shut

Down System

is selected.

When GPS option is
powered by safety circuit, a
loss of power will cause this
error.

E19

GPS Signal Loss
• The Satellite Count

is logged with the
error.

When the GPS Lock Status transi-
tions from Standard to DGPS or
None.
GPS Position must be enabled.

Yes - if Shut

Down System

is selected.

Check for clear path above
the GPS antenna.

E20

DGPS Signal Loss
• The Satellite Count

is logged with the
error.

When the GPS Lock Status transi-
tions from DGPS to Standard.
GPS Position must be enabled.

Check for clear path above
the GPS antenna.

E21

Flow Rate Below Low
Flow Limit

After operating pressure has been
achieved, while the Machine is
running with water On, the flow rate
fell below the low flow limit.
Minimum flow rate must be enabled.

Yes - by Flow

Fault.

Low Flow Limit may be set
too high.

E22

Pressure Above High
Pressure Limit
• Error is logged every

time the water pres-
sure rises above the
High Pressure Limit.

Every time the water pressure rises
above the High Pressure Limit.

Yes - by High

Pressure

Fault after the

High Pres-

sure Shut-

down Delay

time.

High pressure may be set
too low. Verify pressure
transducer is calibrated and
working correctly.

E23

PLC Communication
Error
• The OPMC ID is

logged with the error.

After 3 consecutive command
messages are sent to an OPMC ID
with no reply message being
received.

Verify Correct PLC Channel
and ID Settings.

Figure 57-1

Содержание VRI-iS







































































































Результаты поиска

Содержание VRI-iS

Отзывы:

Похожие инструкции для VRI-iS

Бренды по названию

Популярные бренды

Valley VRI-iS, Руководство по установке

Результаты поиска

Содержание VRI-iS

Отзывы:

Похожие инструкции для VRI-iS

Бренды по названию

Популярные бренды