Valley VRI-iS Скачать руководство пользователя страница 28

Страница: 28 / 102

Installation Instructions

Connect Cables

• Valve to Collector Ring:

Connect the cable from collector ring to the first valve. See Figure 28-1.

• Valve to Valve:

Connect 10 ft cable (with valve) to the VDC OUT port on an Inner valve, then route to the

next valve location and connect to the VDC IN port. See Figure 28-1.

• Valve to Power Supply Tower Box or GPS Tower Box:

Connect the tower box inner valve cable to the inner valve VDC OUT port. See Figure 28-1.

Connect the tower box outer valve cable to the outer valve VDC IN port.

NOTE

• Special attention should be taken when plugging in any connectors. Connectors are keyed and

orientation is labeled with an arrow, however with enough force the connectors can be inserted
incorrectly.

• A power supply tower box is required every 50 valves or less, or every 1000 ft or less, whichever

comes first.

VDC IN

VDC OUT

Figure 28-1 1. Collector Ring

2. Valve

3. Power Supply or GPS Tower Box
4. Optional Valve

Содержание VRI-iS







































































































Результаты поиска

Содержание VRI-iS

Отзывы:

Бренды по названию

Популярные бренды

Valley VRI-iS, Руководство по установке

Результаты поиска

Содержание VRI-iS

Отзывы:

Бренды по названию

Популярные бренды