background image

 

VALCOM SIGNATURE SERIES

TM

, HIGH FIDELITY 

 

SELF-AMPLIFIED IN-WALL SPEAKER 

The Valcom Signature Series™ In-Wall Speaker, V-1450, is a high fidelity, self-
amplified (6 Watt) speaker and may be used to provide one-way paging and high 
quality music reproduction from any Valcom Page Control.  This  speaker has an 
externally accessible volume control located behind the grille and is screwdriver 
adjustable.  The V-1450 will cover an area up to 600 square feet and should be spaced 
20 feet apart.  Good quality paging will be heard up to 30 feet in front of the speaker.  
The V-1450 requires -24VDC, 200mA (4 Valcom power units).  The speaker is available 
in white and supplied with a trim ring and grille. 

 

NOTE:  No power amplifier required.  Do not connect this speaker directly to a 

25/70/100 Volt amplifier as damage to both the amplifier and speaker 
may occur.     (Recommended nominal input level  to the V-1450 is          -
10dBm). 

 
Mounting/Connections 

CAUTION:  Before cutting hole, identify and locate all plumbing and  

     electrical wiring. 

Using the enclosed cutout template, mark outline of cutout on wall.  Make 
sure speaker is centered between any wall studs.  Using the appropriate tool, 
cut a hole in the wall following the template outline. 
 
Insert a small screwdriver tip between the grill and speaker to remove grill from the 
front of the speaker assembly.  Assemble speaker, mounting frame and hardware as 
shown in the diagram.  Do not tighten frame completely. 
 
After assembling mounting frame, make connections to the terminal block.  Insert 
stripped wire into appropriate terminal and tighten with screwdriver.  Each connector 
accepts 18 to 24AWG wire.  With the tweeter on top, place mounting bracket into 
hole in the wall.  Push speaker assembly flush to wall and slide up 

1/2 

inch.  Tighten 

two center screws first, then tighten the remaining screws.  Set volume control to 

1/2

 

volume and test.  Press grill into slot around speaker assembly. 

 

NOTE:   Exercise caution when handling speaker assembly with grill removed. 
 
 

Mounting 

 

 

Dimensions/Weight

 

• 

12.00"H x 8.65"W x 3.20"D (30.48cm H x 21.97cm W x 8.13cm D) 

• 

3

 

lbs (1.36 kg) 

 
FCC  Notice 
NOTE:

 

 

The equipment has been tested and found to comply with the limits for 

Class A digital devices, pursuant to Part 15 of the FCC Rules.  These limits are 
designed to provide reasonable protection against harmful interference when the 
equipment is operated in a commercial environment.  This equipment generates, uses 
and can radiate radio frequency energy.  If not installed and used in accordance with 
the instruction manual, it may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful 
interference in which case the user will be required to correct the interference at his 
own expense. 
 

 

NOTE:

  The manufacturer is not responsible for any radio or TV interference caused 

by unauthorized modifications to this equipment.  Such modifications could void the 
user's authority to operate the equipment. 

Recommended Quantity of Speakers per Specific Power Run

 

 

(Standard Category 3 Twisted Pair Telephone Wire) 

 

 

Speakers per 

 

Power Run 

 

 
 

Wire Run Length (Feet) 

 

 

V-1450 

 

 

24AWG 

 

 

22AWG 

 

 

 

 

 

 

125 

 

250 

 

500 

 

 

200 

 

400 

 

 800 

 
 

Отзывы: