VALCO MELTON DD-1 страница 11 Скачать руководство пользователя | Manualshive

Страница: 11 / 66

background image

2-4

ValcoMelton

Section 2 - Safety Information

MS013 - DD-1 Pump Manual (built after 9/06)

Limitations of
Use

Read this document and all information regarding the equipment before
handling the equipment. The intended use of the equipment is stated in
Section 1 of this manual.

Do not use this equipment for anything other than its intended use. Do not
modify, change, or alter the equipment in any way. If you are unsure of the
intended use and the limitations of use for the equipment, contact your Valco
Melton Representative before handling the equipment.

Installation/
Startup/Use
Safety
Information

WARNING!

WARNING!

WARNING!

WARNING!

WARNING!

Only qualified personnel should install the equipment.
Valco Melton strongly recommends that a Valco Melton
Technician install all equipment. OTHERWISE, DEATH,
PERSONAL INJURY, OR DAMAGE TO EQUIPMENT
COULD OCCUR.

WARNING!

WARNING!

WARNING!

WARNING!

WARNING!

The equipment should be installed so that it can be turned
off at a location away

away

away

away

away from the equipment in case of

injury, electrical problems, or malfunction. OTHERWISE,
DEATH OR PERSONAL INJURY COULD OCCUR.

WARNING!

WARNING!

WARNING!

WARNING!

WARNING!

Properly route all electrical wires. Never tamper with
equipment. Only use approved and correct voltage, type
of current, fuses, and other power supplies. Replace worn
cords, hoses, etc. immediately. FAILURE TO OBSERVE
WARNING MAY RESULT IN DEATH, PERSONAL
INJURY, AND/OR EQUIPMENT DAMAGE.

WARNING!

WARNING!

WARNING!

WARNING!

WARNING!

Poor ventilation, smoking, and open flames can cause
overheated hot melt to ignite. Adequate ventilation must
be provided. Smoking should be prohibited in the
immediate vicinity of the molten adhesive. Open flames
must be kept away from the area around molten adhesive.
OTHERWISE, DEATH, PERSONAL INJURY, OR
DAMAGE TO EQUIPMENT COULD OCCUR.

WARNING!

WARNING!

WARNING!

WARNING!

WARNING!

Never use any Valco Melton equipment in an explosive
environment. Explosive environments include, but are not
limited to, solvent-based cleaners or adhesives, explosive
materials, radioactive materials, etc. OTHERWISE,
DEATH OR PERSONAL INJURY COULD OCCUR.

WARNING!

WARNING!

WARNING!

WARNING!

WARNING!

Equipment will start automatically when remotely
controlled by triggering devices. Be sure to disable all
triggering devices, carefully release hydraulic pressure,
and disconnect air pressure before servicing or working
near guns, valves, and other triggered devices.
OTHERWISE, DEATH OR PERSONAL INJURY COULD
OCCUR.

Valco Melton hot melt units, cold glue units, controllers, inspection systems
and all related accessories have the following universal safety precautions
(this is not intended to be an exhaustive list; follow all instructions and safety
precautions for the specific type of equipment involved):

«
...
9
10
11
12
13
...
»

Содержание DD-1



































































Отзывы:

Нет отзывов

Похожие инструкции для DD-1

Бренд: Watson-Marlow Страницы: 128

Odyssey ODYR-25-1

Бренд: Dakota Digital Страницы: 8

Ingenio VM 050 D400-3-E

Бренд: Atlantic Страницы: 69

Бренд: A.O. Smith Страницы: 48

NEVERCOLD 70600

Бренд: EASTMAN Страницы: 11

Бренд: Crivit Страницы: 23

Бренд: Honda Страницы: 75

Бренд: T.I.P. Страницы: 120

Бренд: Gude Страницы: 40

Бренд: CME Страницы: 28

Бренд: Malibu Boats Страницы: 2

Бренд: Commercial Electric Страницы: 15

Бренд: InSinkErator Страницы: 16

Бренд: Walter Страницы: 12

Бренд: Wacker Neuson Страницы: 208

Бренд: GORMAN-RUPP PUMPS Страницы: 45

1 EPBH 9.2-11 T-AVS

Бренд: EBARA Страницы: 16

ProConnect 19B732

Бренд: Graco Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды