Valco Cincinnati VC350A Скачать руководство пользователя страница 71

Страница: 71 / 327

Valco Cincinnati

10-1

Introduction

This section contains possible solutions to problems you may experience.

Section 10—Troubleshooting

Problem

Possible Cause

Possible Solution

Glue Pattern

At low speed, the
pattern length is too
short or too long.

1a. Either the “flap” or the “glue”

value is incorrect.

1b. Ratio compensation is incorrect.

1a. Ensure that the “flap” and “glue”

values have been correctly
entered.

1b. Ensure that ratio compensation

has been correctly entered.

At low speed, the delay
is too short or too long
before the pattern starts.

2a. “Flap” value is incorrect.

2b. Ratio compensation is incorrect.

2c. Cell-to-gun value is incorrect.

2a. Ensure that the “flap” value has

been correctly entered.

2b. Ensure that the ratio

compensation has been correctly
entered.

2c. Ensure that the cell-to-gun value

has been correctly entered.

At high speed, the
pattern length is too
short or too long.

3a. Either the “flap” or the “glue”

value is incorrect.

3b. Pattern length is incorrect at low

speed.

3c. Either the on or off compensation

is incorrect.

3a. Ensure that the “flap” and “glue”

values have been correctly
entered.

3b. Ensure that the pattern length is

correct at low speed.

3c. Ensure that the on and off

compensations have been adjusted
properly.

At high speed, the delay
is too short or too long
before the pattern
begins.

4a. “Flap” value is incorrect.

4b. “Flap” position is incorrect at low

speed.

4c. “On” compensation is incorrect.

4a. Ensure that the “flap” value has

been correctly entered.

4b. Ensure that the “flap” position is

correct at low speed.

4c. Ensure that the “on”

compensation has been correctly
entered.

There is a drop of glue
at the end of the product

5a. Air in glue line

5b. Glue viscosity too low

5c. Defective O-ring

5d. Too much guide-spring tension

(too much product movement at the
glue station)

5a. Purge air from glue line.

5b. Increase glue viscosity to 1500-

2000 cps.

5c. Replace O-ring.

5d. Decrease guide-spring tension.

Содержание VC350A








































































































































































































































































































































Результаты поиска

Содержание VC350A

Отзывы:

Похожие инструкции для VC350A

Бренды по названию

Популярные бренды

Valco Cincinnati VC350A, Руководство пользователя

Результаты поиска

Содержание VC350A

Отзывы:

Похожие инструкции для VC350A

Бренды по названию

Популярные бренды