Val Controls IDC24-A Скачать руководство пользователя страница 67

Страница: 67 / 74

DID-UM-002

Val Controls A/S

•

Limfjordsvej 3

•

DK-6715 Esbjerg N

•

Tel. +45 7547 0600

[email protected]

•

www.valcontrols.com

Revision: 10

67/74

9.1

Pump unit errors

No. 601

Pump control: Low level.

Description

The measured level is below the specified value.

Trouble shooting

This error can be caused by:

•

Low oil level

•

Mal functioning sensor

•

High value of Level Low limit

It can be solved by:

•

Refill the tank with oil

•

Decrease Level Low limit value

No. 602

Pump control: Temperature.

Description

The measured temperature is above or below the limit values.

Trouble shooting

This error can be caused by:

•

Low oil temperature

•

High oil temperature

•

Sensor malfunction

It can be solved by:

•

Change oil temperature

•

Adjust temperature Low limit

•

Adjust temperature High limit

No. 610

Pump control: Motor safety relay

Description

The motor protection relay is active

Trouble shooting

This error can be caused by:

•

Motor safety relay has been activated

•

Motor safety relay malfunction or disconnected

Содержание IDC24-A











































































Результаты поиска

Содержание IDC24-A

Отзывы:

Бренды по названию

Популярные бренды

Val Controls IDC24-A, Руководство пользователя

Результаты поиска

Содержание IDC24-A

Отзывы:

Бренды по названию

Популярные бренды