background image

V A L   A V I O N I C S   L T D  

I N S   4 2 9   I N T E G R A T E D   N A V I G A T I O N   S Y S T E M  

I N S T A L L A T I O N   A N D   O P E R A T O R ’ S   M A N U A L  

 

Revision 3 

 

 

 

 

 

 

 

 

Page 25 of 27 

March 2013 

 

 

COMMUNICATIONS ERROR 

This message is used to indicate a communication error. 
 

Message format:  

“V” ..................... Message class. This is a VHF NAV message. 
“27” .................... Message identifier. 
e.......................... Error code: (ASCII) 

“0” = input message checksum error. 
“1” = unknown message. 
“2” = error or mismatch in message data. 

 

Example message: 
 

$PMRRV271<chksm><CR><LF> 

 
Received an unknown message.  
 

NAV RECEIVER STATUS 

This message is used to output the current status of the NAV receiver. It will be output upon request or 
whenever the status changes. 
 

Message format: 

“V” ..................... Message class. This is a VHF NAV message 
“28” .................... Message identifier 
mk ...................... Standby NAV frequency: m = MHz, where m + 30h = desired MHz frequency 

in the range of 108 to 117 MHz.  k= (desired frequency / 25 kHz) + 30h, with 
desired frequency in range of 000 to 975 kHz in 50 kHz steps.  

s.......................... Status: “N” = Normal mode, “M” = Monitor mode 

 

Example message:  
 

 

$PMRRV28E4?PM<chksm><CR><LF> 

 
Active NAV frequency is 117.100 MHz, Standby NAV frequency is 111.800 MHz, receiver is in monitor 
mode.  
 

NAV M

ICROCONTROLLER 

S

OFTWARE 

V

ERSION

 

This message is used to output the version string for the NAV microcontroller software. 
 

Message format: 

“V” ..................... Message class. This is a VHF NAV message. 
“30” .................... Message identifier. 
vvvv ................... Software version in ASCII 
e.......................... Engineering version flag: 

“R” = Released version. 
“E” = Engineering version. 

 

Example message: 
 

$PMRRV300103E<chksm><CR><LF> 

 
NAV Microcontroller software is version 1.03. It is an engineering version.  
 

C

OM 

T

RANSCEIVER 

S

TATUS

 

This message outputs the result of a specific system test. 
 

Message format: 

“V” ..................... Message class. This is a VHF NAV message. 

Содержание COM 2KR




























Отзывы: