manualshive.com logo in svg

Vaisala MGP261, Руководство пользователя

Поделиться
Скачать
Vaisala MGP261 Скачать руководство пользователя страница 32

3.5 Finalizing Installation

PULL INSTRUMENT OUT

BEFORE CLOSING VALVE

1

3

2

≥ 

4 mm2

1

Safety pin: in ball valve installations, lock the handle of the ball valve in the open position
with the safety pin to prevent damage caused by closing the valve with the instrument
inside.

2

MGP261 grounding terminal.

3

Use a 

≥

 4 mm

2

 wire to connect the grounding terminal to the grounding rail of the

installation site.

1. Close and tighten the connection box (< 0.55 mm cover gap) and cable glands, and

tighten the probe to final tightness on the installation port by turning the tightening nut

with the wrench.

2. Connect the MGP261 grounding terminal to the grounding rail of the installation site with

a 

≥

 4 mm

2

 wire.

3.

Ball valve installations only:

 lock the handle of the ball valve in the open position with

the safety pin.

4. When done, switch on the power supply input.

More Information

‣

Installation Type Configuration in Insight (page 33)

MGP261 User Guide

M212273EN-A

30

Содержание MGP261



























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды