Vaisala MGP260 Series Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 92

Vaisala MGP260 Series Скачать руководство пользователя страница 45

7. Environmental compensation

7.1 Overview

When necessary, environmental compensations can be applied to improve the measurement
accuracy (for example, to provide the probe with a real-time pressure reading from the
measurement environment by using input from an external sensor).

The probe can compensate for the effects of the following parameters:

• Temperature (T)
• Pressure (P)

Environmental compensation parameters can be provided to the probe from the following
sources:

• The internal temperature sensor of the probe can be used for temperature compensation.
• An external sensor can be connected to the probe (4 … 20 mA analog input, Ex ia) to

provide temperature or pressure compensation values.

• If the temperature and pressure values are known and remain constant, they can be

entered as fixed setpoint values.

• If the probe is integrated in a system that measures either temperature or pressure, they

can be updated to the probe continuously.

The method used for environmental compensation is configured on the order form when
ordering the probe, and can later be updated using Vaisala Insight PC software or Modbus
protocol.

7.1.1 Temperature compensation

MGP260 can measure the approximate temperature of the CARBOCAP

â

sensor for

compensation, use a fixed setpoint value as the temperature compensation, or receive the

temperature compensation value from an external temperature sensor.

Unless a dedicated temperature measurement is available and can be regularly updated to the

probe, it is strongly recommended to use the probe's internal temperature compensation to

ensure real-time accurate measurements. If the measurement is made in a constant

temperature, the constant temperature can be set as the compensation value (fixed setpoint

option).

7.1.2 Pressure compensation

The probe does not have on-board pressure measurement. You can either configure a fixed

setpoint value that is used as the pressure compensation, or set the probe to receive the

pressure compensation value from an external pressure sensor.

Chapter 7 – Environmental compensation

43

陕西威瑞仪器仪表有限公司生产代理销售：实验检测设备气象科学仪器设备

Tel:029-88186182 Web:www.xavery.cn Email:[email protected]

«
...
43
44
45
46
47
...
»

Содержание MGP260 Series





























































































Отзывы:

Нет отзывов