background image

Table 8 Standards and Compliance

Property

Specification

Safety standard

IEC/UL/EN 61010-1

Networking standards (wireless configuration

interface WLAN access point)

IEEE 802.11 b/g/n compliant

Electromagnetic compatibility

Complies with EMC standard 

EN61326-1 Generic

Environment

Contains

FCC ID QOQ-WGM110
IC 5123A-WGM110

当該機器には電波法に基づく、技術基準適合証明等
を受けた特定無線設備を装着している。

R 209-J00197

Table 9 Wireless Access Point (Module With Internal Chip Antenna)

Property

Specification

Networking standards

IEEE 802.11 b/g/n

Data rates

802.11 b: 1, 2, 5.5,11 Mbps : 802.11 g: 6, 9, 12, 18

Frequency band

2402 ~ 2480MHz

Modulation

802.11 b: DSSS (CCK-11, CCK-5.5, DQPSK-2,DBPSK-1):
802.11g : OFDM Wi-Fi

Security

WEP (128-bit), WPA, WPA2 (Personal)

Output power

+16DBm

Receiver sensitivity

-85dBm typical

Table 10 Operating and Storage Environment

Property

Specification

Operating temperature range

-20 ... + 60 °C (-4 ... + 140 °F)

Storage temperature range

-40 ... +70 °C (-40 ... 158 °F)

Operating humidity range

0 ... 100 %RH (non-condensing)

Chemical tolerance

Temporary exposure during cleaning:

• H

2

O

2

 (6000 ppm, non-condensing)

• Alcohol-based cleaning agents such as ethanol and

IPA (max. 70 % concentrate)

• CaOCI (hypochlorite) max. 0.5 %
• QAC (quaternary ammonium cations) max. 0.5 %)

Indigo 202 User Guide

M211966EN-A

62

Содержание Indigo 202













































































Отзывы: