Vaisala HMP7 Скачать руководство пользователя страница 40

Страница: 40 / 96

Only the HUMICAP

R2 sensor is designed to be replaced by the

user. Other humidity sensor types available for HMP series probes are composite
sensors where the humidity sensor and temperature sensor are permanently
attached together. If you need to replace a composite sensor, contact a Vaisala
Service Center.

CAUTION!

Sensors are easily damaged when the filter is not in place. Handle

the probe head carefully.

CAUTION!

Reverting the probe to factory settings clears the adjustment values

entered in this procedure. If you need to revert the probe to factory settings
after replacing the sensor yourself, write down the values on the

Adjustment

data

page beforehand, and enter them again after applying the factory settings.

CAUTION!

Figure 22 HMP3 probe head with filter removed

Pt100 temperature sensor

HUMICAP

R2 humidity sensor

1. Put on clean gloves before touching the filter.

2. Turn the filter counter-clockwise to loosen it.
3. Remove the filter from the probe head. Be careful not to touch the sensors with the filter.

4. There are two sensors under the filter, the HUMICAP

sensor and a temperature sensor.

Identify the HUMICAP

sensor and make sure it is of the R2 type (temperature sensor not

attached to it).

HMP3, HMP4, HMP5, HMP7, HMP8, HMP9, MMP8, TMP1 User Guide

M212022EN-D

陕西威瑞仪器仪表有限公司生产代理销售：实验检测设备气象科学仪器设备

Tel:029-88186182 Web:www.xavery.cn Email:[email protected]

Содержание HMP7

































































































Результаты поиска

Содержание HMP7

Отзывы:

Vaisala HMP7, Руководство пользователя, Страница: 40 / 96

Результаты поиска

Содержание HMP7

Отзывы: