Vaisala HMP7 Скачать руководство пользователя страница 39

Страница: 39 / 96

6.2 Changing the probe filter

• New compatible filter
• Clean lint-free gloves

Sensors are easily damaged when the filter is not in place. Handle

the probe head carefully.

CAUTION!

HMP9 and TMP1 probe models do not have a removable filter.

1. Put on clean gloves before touching the filter.

2. Turn the filter counter-clockwise to loosen it.
3. Remove the filter from the probe head. Be careful not to touch the sensors with the filter.

4. Install a new filter on the probe head. Tighten the filter properly (recommended force

5 Nm).

6.3 Replacing the HUMICAP R2 sensor

• New HUMICAP

R2 sensor

• New compatible filter
• Clean lint-free gloves
• 11.3 %RH and 75.5 %RH humidity references (using Vaisala HMK15 Humidity

Calibrator)

• Computer with Microsoft Windows

operating system and Vaisala Insight

software installed

• USB connection cable (no. 242659)

Follow this procedure to replace a HUMICAP

R2 humidity sensor it has been damaged, or

normal adjustment is not sufficient to restore the humidity measurement accuracy. It is

recommended that you replace the filter at the same time. The procedure includes a special 2-

point adjustment of humidity measurement using Insight PC software. This adjustment must

be done every time after the HUMICAP

R2 sensor has been replaced.

Chapter 6 – Maintenance

陕西威瑞仪器仪表有限公司生产代理销售：实验检测设备气象科学仪器设备

Tel:029-88186182 Web:www.xavery.cn Email:[email protected]

Содержание HMP7

































































































Результаты поиска

Содержание HMP7

Отзывы:

Vaisala HMP7, Руководство пользователя, Страница: 39 / 96

Результаты поиска

Содержание HMP7

Отзывы: