Vaisala HMP3 Скачать руководство пользователя страница 25

Страница: 25 / 96

2. Use a threading tap to create a M10×1.5 thread in the hole.
3. Install the base of the cable gland in the hole and tighten with a 13 mm wrench.

4. Insert the seal of the cable gland in the base and place the nut of the cable gland over the

probe head.

5. Insert the probe head in the cable gland up to the black plastic part of the probe head.

Leave the black plastic part entirely outside the cable gland. Tighten the cable gland to
finger tightness.

6. Tighten the nut of the cable gland with a 13 mm wrench until the probe head stops

moving. Do not overtighten.

3.7 MMP8 probe

136 [5.35]

Probe cable 2 m [6.56 ft]

Ø 25 [0.98]

M12/5

Ø 5 [0.2]

[in]

262 [10.32]

224 [8.82]

35 ... 179 [1.37 ... 7.05]

35 [1.37]

Ø 13.5 [0.53]

Fitting body

ISO1/2” or NPT1/2”

Ø 12 [0.47]

Figure 11 MMP8 dimensions

Vaisala HUMICAP

Moisture in Oil Probe MMP8 enables fast and reliable measurement of

moisture in oil. It uses proven Vaisala HUMICAP

sensor that was developed for demanding

dissolved moisture measurements in transformer and lubrication oils, hydraulic fluids, and

other liquids.

MMP8 measures dissolved moisture in oil in terms of the water activity (a

), relative saturation

(%RS), and temperature (T). Water activity or relative saturation indicate directly whether

there is a risk of free water formation. This data is relevant in lubrication oil applications where

detecting water ingress and preventing free water formation is crucial. The measurement is

independent of oil type and age.

Chapter 3 – Installation

陕西威瑞仪器仪表有限公司生产代理销售：实验检测设备气象科学仪器设备

Tel:029-88186182 Web:www.xavery.cn Email:[email protected]

Содержание HMP3

































































































Результаты поиска

Содержание HMP3

Отзывы:

Бренды по названию

Популярные бренды

Vaisala HMP3, Руководство пользователя

Результаты поиска

Содержание HMP3

Отзывы:

Бренды по названию

Популярные бренды