manualshive.com logo in svg

Vaisala AWS310-SITE, Руководство по настройке и обслуживанию

Поделиться
Скачать
Vaisala AWS310-SITE Скачать руководство пользователя страница 40

4.4.5 Setting Messaging Parameters

Although AWS310-SITE lists all the available parameters, you can only edit the settings for
hardware that is correctly installed and configured in the system.

To define the interface settings and to send the air temperature and relative humidity
message (TU) and atmospheric pressure message (PA) to the WID displays, set the correct
messaging parameters.

1. In AWS Client, select 

Settings > Parameters > Static

.

2. In the 

MessageDispatcher

 parameter set, configure the messaging parameters. The

possible values are 

0

 (disabled) and 

1

 (enabled). 

Parameter Name

Description

reports_to_local

Sends reports to local serial port on 

DSI486_0_1

.

reports_to_local2

Sends reports to local serial port on 

DSI486_1_1

.

reports_to_com0

Sends reports to local service port 

COM0

.

TU_WID

Sends the TU message to WID displays.

PA_WID

Sends the PA message to WID displays.

3. To save the changes, select 

Save

.

4.5 Configuring Sensor Parameters

To add preconfigured sensors in or to remove existing sensors from the configuration,
enable the sensors that are included in the weather station.

Do not enable sensors that are not part of the system. This may cause

errors.

CAUTION!

1. In AWS Client, select 

Settings > Parameters > Static

.

2. Open the 

CFG

 parameter set.

AWS310-SITE Configuration and Maintenance Manual

M211828EN-C

38

Содержание AWS310-SITE

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды