Vaisala AWS310-SITE Скачать руководство пользователя страница 33

Страница: 33 / 176

5. In

Serial Port

, set the following:

COM port

The COM port to which the service cable is connected to.
In the

Default

station, the COM port is set to

. To make sure this matches the port

assigned for the USB serial port, launch the Vaisala USB Instrument Finder
program from the

Start

menu.

Baud rate

Set to

9600

Parity

Set to

None

Data bits

Set to

Stop bits

Set to

Flow control

Set to

None

6. The

Telephone

section is not needed. Leave it empty.

7. To save the changes, select

Save

4.3.2 Establishing Connection to Station

1. In AWS Client, select

File > Connect

2. To establish a connection, select the correct weather station and

When you are connected to the station but the service connection is closed, messages and
reports appear in the main window.

The report type and appearance depend on your setup. The messages and reports only
appear if they are configured in the station.

Some values are shown as slashes, either because the sensor is missing or because the
value is calculated from the measured values later.

4.3.3 Changing COM Port

1. In AWS Client, select

Settings > Address Book

2. Select the appropriate station and

Edit

Chapter 4 – AWS Client Usage

Содержание AWS310-SITE

















































































































































































Результаты поиска

Содержание AWS310-SITE

Отзывы:

Бренды по названию

Популярные бренды

Vaisala AWS310-SITE, Руководство по настройке и обслуживанию

Результаты поиска

Содержание AWS310-SITE

Отзывы:

Бренды по названию

Популярные бренды