manualshive.com logo in svg

Vaisala AWS310-SITE, Руководство по настройке и обслуживанию

Поделиться
Скачать
Vaisala AWS310-SITE Скачать руководство пользователя страница 20

Do not substitute parts or modify the system, or install unsuitable parts in

the system. Improper modification can damage the product or lead to malfunction.

WARNING!

Failure to comply with these precautions or with specific warnings

elsewhere in these instructions violates safety standards of design, manufacture, and
intended use of the product. Vaisala assumes no liability for the customer's failure to
comply with these requirements.

WARNING!

If the equipment is used in a manner not specified by Vaisala, the

protection provided by the equipment may be impaired.

WARNING!

Do not damage or change the wiring. Incorrect wiring can cause damage

and prevent or limit operation.

CAUTION!

2.3.1 ESD Protection

Electrostatic Discharge (ESD) can damage electronic circuits. Vaisala products are
adequately protected against ESD for their intended use. However, it is possible to damage
the product by delivering electrostatic discharges when touching, removing, or inserting any
objects in the equipment housing.
To avoid delivering high static voltages to the product:

• Handle ESD-sensitive components on a properly grounded and protected ESD

workbench or by grounding yourself to the equipment chassis with a wrist strap and a
resistive connection cord.

• If you are unable to take either precaution, touch a conductive part of the equipment

chassis with your other hand before touching ESD-sensitive components.

• Hold component boards by the edges and avoid touching component contacts.

2.4 Regulatory Compliances

This product is in compliance with the Australian RCM regulation and the following
European Union directives:

• Low Voltage Directive (2006/95/EC)
• EMC Directive (2004/108/EC)

 

AWS310-SITE Configuration and Maintenance Manual

M211828EN-C

18

Содержание AWS310-SITE

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды