Vaisala AWS310-SITE Скачать руководство пользователя страница 17

Страница: 17 / 176

Item

Name

DKP12SUP1
DKP12SUP2

Vaisala sensor support arm for 100

‑

mm (3.94

‑

in) masts, half-length or full-length

DKL201

Vaisala Lightning Kit

Table 5 Sensors

Item

Name

WMT700

Vaisala WINDCAP Ultrasonic Wind Sensor

WA15:

• WAA151
• WAV151
• WAC155

Vaisala Wind Set consisting of:

• Vaisala Anemometer
• Vaisala Wind Vane
• Vaisala Serial Transmitter

HMP155

Vaisala HUMICAP Humidity and Temperature Probe

CMP3
CMP6
CMP10

Kipp & Zonen Pyranometer

FS11

Vaisala Visibility Sensor

PWD22

Vaisala Present Weather Detector

CL31

Vaisala Ceilometer

QMT107
QMT110

Vaisala Soil/Water Temperature Sensor

RG13(H)

Vaisala Rain Gauge (with heating)

OTT Pluvio

OTT Precipitation Gauge

PTB330

Vaisala BAROCAP Digital Barometer

2.3 Safety

This product has been type-tested for safety and approved as shipped from the factory.
Note the following precautions:

Consult local electricity professionals for the local and state legislation

and regulations about grounding.

WARNING!

Ground the product and verify outdoor installation grounding

periodically. Failure to provide proper grounding can result in injury or death from
electrical shock and can severely damage the equipment.

WARNING!

Chapter 2 – Product Overview

Содержание AWS310-SITE

















































































































































































Результаты поиска

Содержание AWS310-SITE

Отзывы:

Бренды по названию

Популярные бренды

Vaisala AWS310-SITE, Руководство по настройке и обслуживанию

Результаты поиска

Содержание AWS310-SITE

Отзывы:

Бренды по названию

Популярные бренды