manualshive.com logo in svg

Vaisala AWS310-SITE, Руководство по настройке и обслуживанию

Поделиться
Скачать
Vaisala AWS310-SITE Скачать руководство пользователя страница 139

Problem

Probable Cause

Remedy

Precipitation output is

invalid. The USB interface
is connected.

The active USB interface

suspends the output of
intensity, accumulated

precipitation amount, and

impulses.

Disconnect the USB interface.

–

Using the sensor's operating software, run a guided
accuracy test.

Hardware failure.

Replace the sensor.

Precipitation output is
invalid. The USB interface
is not connected.

Hardware failure.

Replace the sensor.

6.10 Troubleshooting Power Supply

Table 37 Problem Situations and Remedies with Power Supply

Problem

Probable Cause

Remedy

Power supply LED is not on.

AC power is missing or AC power
supply is defective.

Check that AC (mains) power is
connected and that the AC power

connectors are properly attached.
Replace AC power supply if
needed.

System appears completely down
when powered on DC input.

DC power supply is missing.

Check that DC power is connected.

System shuts down immediately
when external power supply is cut

off. Battery backup does not work.

Battery circuit is open.

Check the battery wiring.

Battery fuse is off.

Check that the battery fuse is on.

Battery backup time is too short.

Backup batteries are defective.

Check the batteries and replace if
needed.

Chapter 6 – Troubleshooting

137

Содержание AWS310-SITE

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды